Contact Home Links Search

Fans

Related
Information


USGR

Acme Fans - SuperWindmaster

Acme Super Windmaster belt driven fanDC SERIES (STEEL)

  • Six-bladed propeller utilizing a cambered - twist blade designed with a unique dihedral tip for higher air flow capacities at less horsepower.
  • Non-overloading design maintains horsepower within catalog range of static pressure, resulting in lower motor load and reduced operating costs.
  • Streamlined orifice insures higher air flow capacity.
  • Available mounted in either slant or square wall housing.
ACMA sealAcme Engineering and Manufacturing Corporation certifies that the Super Windmaster DC shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 211 and AMCA Publication 311 and comply with the requirements of the AMCA Certified Ratings Program.

SEALED BEARINGS

  • Sealed, pre-lubricated bearingsPrelubricated oversize ball bearings are double sealed, require no service.
  • Improved, more efficient drive assembly and super-duty neoprene belts provide longer service life.

ENERGY EFFICIENT ENCLOSED MOTORS

  • Heavy duty totally enclosed motors with shielded ball bearings are designed for continuous work load.
  • Available in two speed.
  • Built-in thermal overload for low-line voltage protection on all single phase motors.

MOTOR NOTES

  1. All single speed single phase motors are dual voltage (115/230) except 1/4 horsepower.
  2. All 1/4 horsepower single phase motors are single voltage (115 or 230).
  3. Two-speed motors are single voltage (115 or 230) and not available in 11/2 horsepower.
  4. Low speed capacity of two speed fans is approximately one half of maximum.
  5. All three phase motors are triple voltage (200-230/460).

 

field installation
Field installation of an Acme SuperWindmaster -1979 China

Very old SuperWindmaster
25 year old Acme Fan - still working. A little rusty but only repair was
renewed fan belt - bearing replaced once - Seattle Washington - Acme fans
run effectively for generations

CERTIFIED CFM VS. STATIC PRESSURE (INCHES WG) MAX
STATIC
PRESSURE
FAN HP  RPM .000” .050” .100” .125” .150”
CFM *BHP C/W CFM *BHP C/W CFM *BHP C/W CFM *BHP C/W CFM *BHP C/W
DC24E 1/4 622 5280 0.25 18.3 4950 0.25 17.1 4530 0.26 15.5 4235 0.26 14.5 3870 0.25 10.8 0.150
DC24F 1/3 735 6235 0.41 14.5 5960 0.41 13.8 5655 0.42 13.0 5475 0.42 12.5 5255 0.42 12.0 0.250
DC24G 1/2 820 6960 0.57 12.1 6715 0.57 11.7 6450 0.57 11.2 6305 0.58 10.9 6145 0.58 10.6 0.300
DC24G-2S 1/2 763 6475 0.46 14.0 6210 0.46 13.3 5920 0.46 12.7 5755 0.47 12.3 5555 0.47 11.8 0.250
DC24H 3/4 949 8055 0.88 9.2 7840 0.88 8.9 7625 0.89 8.7 7510 0.89 8.5 7390 0.89 8.4 0.300
DC24H-2S 3/4 875 7425 0.69 10.8 7195 0.69 10.4 6955 0.70 10.1 6825 0.70 9.9 6685 0.70 9.6 0.375
DC30F 1/3 529 8475 0.40 20.1 7985 0.41 18.6 7400 0.42 17.0 7010 0.42 16.1 6560 0.41 15.2 0.200
DC30G 1/2 607 9725 0.61 15.9 9305 0.61 15.0 8840 0.62 13.3 8570 0.63 13.6 8255 0.63 13.1 0.250
DC30G-2S 1/2 546 8745 0.44 19.7 8275 0.45 18.3 7720 0.46 16.8 7365 0.46 16.0 6950 0.46 15.2 0.200
DC30H 3/4 686 10990 0.87 12.7 10620 0.88 12.1 10230 0.89 11.5 10015 0.90 11.2 9780 0.90 10.9 0.300
DC30H-2S 3/4 647 10365 0.73 14.2 9970 0.74 13.5 9550 0.75 12.8 9310 0.75 12.4 9040 0.76 12.0 0.300
DC36F 1/3 431 10255 0.35 28.3 9570 0.36 25.2 8790 0.38 22.3 8300 0.38 20.8 7660 0.39 18.9 0.150
DC36G 1/2 495 11780 0.52 22.4 11190 0.54 20.5 10555 0.56 18.7 10200 0.57 17.8 9805 0.57 17.0 0.200
DC36G-2S 1/2 463 11015 0.43 25.5 10390 0.45 23.1 9680 0.46 20.8 9265 0.47 19.6 8795 0.47 18.4 0.200
DC36H 3/4 575 13680 0.82 16.8 13175 0.84 15.7 12650 0.86 14.8 12375 0.87 14.3 12085 0.88 13.8 0.300
DC36H-2S 3/4 511 12160 0.58 21.2 11595 0.60 19.6 10985 0.61 18.0 10640 0.62 17.2 10260 0.63 16.4 0.250
DC36J‡ 1 634 15085 1.10 14.0 14630 1.12 13.3 14160 1.15 12.6 13915 1.16 12.3 13665 1.17 11.9 0.300
DC42G 1/2 385 14445 0.54 26.5 13550 0.56 24.1 12490 0.58 21.5 11830 0.58 20.1 11110 0.59 18.7 0.150
DC42G-2S 1/2 356 13355 0.43 31.0 12385 0.44 27.7 11125 0.46 24.1 10410 0.47 22.1 9610 0.48 20.1 0.150
DC42H 3/4 442 16580 0.82 20.4 15815 0.84 19.0 14970 0.86 17.6 14475 0.87 16.8 13915 0.88 16.0 0.250
DC42H-2S 3/4 511 15495 0.67 23.4 14670 0.69 21.5 13725 0.71 19.6 13145 0.71 18.6 12520 0.72 17.4 0.300
DC42J‡ 1 485 18195 1.08 17.2 17500 1.10 16.2 16760 1.12 15.2 16350 1.14 14.7 15890 1.15 14.2 0.300
DC48G 1/2 308 17470 0.55 31.8 16220 0.57 28.4 14650 0.58 24.9 13630 0.59 22.9 12160 0.61 19.9 0.150
DC48G-2S 1/2 276 15655 0.39 39.5 14230 0.41 34.4 12230 0.43 28.6 10075 0.45 22.1 - - - 0.125
DC48H 3/4 354 20080 0.83 24.4 19005 0.86 22.3 17795 0.87 20.5 17065 0.88 19.4 16225 0.89 18.3 0.200
DC48H-2S 3/4 314 17810 0.58 31.0 16585 0.60 27.9 15080 0.62 24.6 14105 0.62 22.7 12865 0.64 20.3 0.150
DC48J‡ 1 382 21670 1.04 21.2 20675 1.07 19.8 19600 1.09 18.3 18980 1.10 17.6 18285 1.11 16.8 0.200
DC48K 11/2 444 25,185 1.63 16.4 24,335 1.66 15.5 23,450 1.69 14.5 22,980 1.71 14.1 22,475 1.72 13.8 0.300
DC54-4J‡ 1 355 26395 1.14 24.0 24560 1.17 21.7 22660 1.19 19.7 21655 1.19 18.8 20570 1.20 17.7 0.200

 

‡ Available with two-speed motor in 230/1 only.
Sound ratings on Model DC are shown in Catalog C2.
Performance shown is installation type A - Free inlet, Free outlet.
* Power (BHP) does not include drive losses.
Performance ratings do not include the effects of appurtenances in the airstream.
CFM per Watt does not include drive losses. C/W ratings are not licensed to bear the AMCA seal.

WARNING! DO NOT use in HAZARDOUS ENVIRONMENTS where fan's electrical system could provide ignition to combustible or flammable

CAUTION! Guards are strongly recommended when the fan is installed within seven (7) feet of the floor, working level or within reach of personnel. Guards complying with OSHA regulations are available as optional equipment. Review OSHA Codes and obtain a quotation.

DC series belt tightenerBELT TIGHTENERS FOR DC SERIES:

Keep fan performance

Copyright © 1998-2013 U.S. Global Resources (USGR). All rights reserved.
Contact USGR :: Top
Web site developed by Infothai CM Co., Ltd.