Seed Processing Equipment
There are three elements, air,
temperature and humidity, that if engineered correctly will result in precision
seed drying. Air, its quality, temperature, and movement, have an enormous
impact on seed conditioning and productivity. We have discovered that many
seed drying problems are caused by an unbalanced drying system. In other words,
for every cubic foot of air exhausted an equal amount must be replaced. The
simple solution is the exchange of makeup air with fresh air. Most importantly,
the introduction of make-up air eliminates air contamination, exchanges stale
air or humidity, eliminates un-proportional air, and maintains proper air stratification
for proper seed drying conditions.
STS-1B-30C, STS-3C Seed Dryer Systems,
Cabinet Chamber Systems
Seed Drying Features
- STS chamber dryers are designed and engineered for precision of temperature,
humidity and air flow for drying all varieties of seed.
- Seed drying must be as versatile as possible. Yet, the products' temperature,
humidity and air flow have to be accurate. If they are not, under drying
or over drying can occur. The STS dryers are designed to provide this accuracy.
- The STS dryer cabinet/chamber models trap air and humidity with precise
calibrated temperature and discharge them at a given rate based on seed density
and seed moisture content.
- The operator has the control to increase or decrease the amount of air
velocity in the front portion of the dryer plenum. This control allows the
operator to increase or discharge excess amounts of air as needed with regards
to drying load capacity.
- Each drying box or chamber has its own damper adjustment. Either to balance
air velocity or close off a section.
- Each drying box or chamber section can be calibrated with air velocity
different from the other damper section or chambers at anytime.
- The STS electric and gas model heating units are both versatile in air
flow to provide a more detailed velocity requirement. The Gas Model, however,
uses speed control motors and bleeder dampers to adjust air speed and pressure.
Seed Dryer Heating Components
- Modulating Controller - Gas Models
STS Dryer systems use a modulating controller to keep the temperature
band as tight (narrow) as possible to eliminate heat swing.
The modulating controller senses the temperature of the discharged air
and proportions the gas input to load demand. When the temperature is below
the controller setting, the burner will modulate to high fire. As the air
temperature approaches the controller setting the modulating gas valve will
close in small increments until the control point temperature is maintained.
As the discharge air temperature falls below the control point setting,
a reverse cycle takes place opening the modulating gas valve trying to maintain
at least a 3-50F heat swing. Again, as tight of a heat band as possible
- Electric Models
All electric model heating units are versatile to heat settings. Our
electric air flow is calibrated by a variable speed controller Also available
is a motor switch control for two speed setting. The heat is controlled
by staggering heat elements to keep a consistency of calibrated heat throughout
the drying regime. This is to provide a gentle cycle at all times. The dryer
can keep temperature consistent to 1 degree heat swing with mild (tight
band) heat swing cycling.
Proven Seed Drying
Through our experience we have found that air flow in relation to moisture
content in the seed has a great advantage if dried gently and evenly The air
releasing excess moisture from the seed at a slow discharge in a stratified
chamber will keep the tissue of the seed plump, and won't allow inconsistency
throughout the seed bed. This will allow the seed to reach the desired moisture
content; but Will provide plump, vigorous and long term viable seed. This is
also an important drying process to have dried plump seed to get a precision
upgrade when separating seed for its final stages.
STS-1B2-30C Seed Dryer Specifications (Forklift Operation)
|Bulk Lot Box & Lid:
Stainless steel screens to customer's specifications
- Cabinet chamber and 8 Interior slide-out drawers
- Bulk lot box chamber with stainless steel lid
230 v, 30, 50/60 Hz
STS-3C Seed Dryer System
Stainless steel screens to customer's specifications
We can design any type of dryer system to customers specifications,
including electrical requirements.
We reserve the right to change or modify design on standard
dryer models at any time.
STS-1C CABINET CHAMBER SYSTEM (Gas)
The 1C Dryer (gas) has the exact specifications as mentioned above. The gas model units have a centrifugal blower, Propane or
Natural gas, Modulating gas valve, Duct temperature sensing, Burner on/off thermostat, and other features. The gas heating
units have a two year factory parts warranty. Electrical requirements: Customers Specifications
STS-2C CABINET CHAMBER SYSTEM (Gas)
Dryer specifications are the same as above. 2500 CFM of air flow @ 3" of static pressure. Total of 12 trays ~600 lbs of
seed total depending on species. Electrical requirements: Customers Specifications.
STS-3C CABINET CHAMBER SYSTEM (Gas)
Same as above. Total 18 trays at a total of ~ 900 lbs, per system. Electrical requirements: Customers Specifications
STS-4C CABINET CHAMBER SYSTEM (Gas)
Same as above. Electric specifications is the same.
Electrical requirements: Customers Specifications
PRICES EXCLUDE CRATING, SHIPPING & HANDLING.
Approximate price depends upon accessories, style or type, voltage and seed specie. Prices vary depending upon multiple options. On large units, request for prices.